[email protected]

(PDF) HOT ROLLED STEEL SHEET HOT ROLLED STEEL SHEET

Dimensional tolerance Dimensional tolerance 2. Thickness shall be measured at any point on the steel strip not less than 25mm from a side edge for the mill edge 12.5 , 14.0 ±0.38 ±0.39 ±0.40 ±0.50 strip 50mm or over in width and cut lengths therefrom, and on ASTM A1011 - SSABThe A1011 specification is the Standard Specification for light gauge Hot-Rolled Sheet and Strip Carbon (CS and DS), Structural (SS), High-Strength Low-Alloy (HSLAS), High-Strength Low-Alloy with Improved Formability (HSLAS-F), and Ultra-High Strength (UHSS) steels in

ASTM ASTI Thickness Tolerance - Coyote Steel

h.r. flat bar hot rolled mild steel 3/4x 1 2.550 51.00 1-1/4 3.188 63.76 1-1/2 3.825 76.50 1-3/4 4.463 89.26 2 5.100 102.00 2-1/2 6.375 127.50 3 7.650 153.00 3-1/2 8.925 178.50 4 10.200 204.00 4-1/2 11.480 229.60 5 12.750 255.00 5-1/2 14.030 280.60 6 15.300 306.00 7 17.850 357.00 8 20.400 408.00 7/8x 1 2.975 59.50 1-1/4 3.719 74.38 1-1/2 4.463 89.26 1-3/4 5.206 104.10 2 5.950 119.00 2-1/4 6 ASTM Equivalent to JIS G3131 SPHC - CR4 Discussion ThreadFeb 17, 2009 · Re:ASTM Equivalent to JIS G3131 SPHC. Max. As sheet/strip this would chemically meet astm a 109, probably astm a570, possibly grade 1012 to astm a 635 if heavy thickness; if plate, astm a 6 and astm a36 structural are possibilities; a 20 if pressure vessel. These are possible nominal equivalent standards to investigate. China Steel And Nippon Steel Vietnam Joint Stock CompanyJIS SAPH 310~440 products are specially designed for automobile structural use, tensile strength from 310 to 440 N/mm2, which can be used in automobile structural applications. ASTM A1011/1018 HSLA GRADE 60~80. High strength low-alloy P/O steel coils mainly applicable to structural use such as sections and stiffening plates.

JIS G 3131-Commercial Hot Rolled SPHC Steels Material

Mar 11, 2012 · The applicable thickness for this SPHC material as defined in the JIS 3131 starts from 1.2 mm to 14 mm. However, the width of SPHC material ranges to 2000 mm. The Chemical Composition of SPHC Steels. JIS G 3131 defines the chemical composition of SPHC steels as under:Maximum percentage of Carbon (C) is 0.15 percent. JIS G3101 SS400 Structural Carbon Steel Plate SpecificationAdvantages of JIS G3101 SS400:Compared with other steel standard, steel products made of ss400 carbon steel is popular for proper tensile strength and toughness, good plasticity, welding performance and processing property. Steel plate thickness has wide range-from steel sheet to super heavy steel plate. JIS G3131 PDF - Mi PDF CityMay 06, 2020 · JIS G 3131-Commercial Hot Rolled SPHC Steels. The relationship between each elongation value and the conversion factor is as follows:It is commonly produced in the range of thickness 1. Consequently JIS G SPHC steel is a commercial quality hot rolled steel. Report in JIS G when required by the purchaser in advance.

JIS G3131,JIS G3131 carbon steel supplier - JOIN WIN STEEL

JIS G3131 Low carbon steel plate and steel strip. Standard:JIS G3131 Steel Grade :HR1, HR2, HR3, HR4, SPHC, SPHD, SPHE, DD11, DD12, DD13, DD14 Tiêu chun JIS G3131 - 123docz.netMar 31, 2015 · It is commonly produced in the range of thickness 1.6 mm to 12.5 mm inclusive, and in widths of 600 mm and over, in coil and cut lengths. U001en Hot-Rolled Steel Sheets and CoilsJIS G 3131 Hot-Rolled Mild Steel Sheets and Coils Examples of Standards Chemical Compositions and Mechanical Properties Designation Chemical Composition (%) Tensile Test Bending Test Tensile Strength (N/mm2) Elongation (%) Test Piece Bending Angle Inner Diameter Thickness (mm) Test Piece 1.2 t 1.6 1.6 t 2.0 Thickness (mm) 2.0 t2.5 Thickness (mm)

JIS G 3131 SPHE steel plate/sheet for stamping and cold

Chemical composition, unit% of JIS SPHE steel Symbol Chemical composition C max Mn max P max S max SPHE 0.10 0.50 0.030 0.035 Mechanical properties of JIS SPHE steel JIS G3131 SPHC/ SPH D steel plate /sheet ,JIS G3131 SPHC/ SPH D steel plate/sheet ,under JIS standard, we can regard SPHE steel plate/sheet as stamping and cold forming steels .JIS