[email protected]

A252 Steel Piling Pipe ASTM/ASME A252/SA252 Piling Pipe

ASTM Specification A252 describes nominal (average) wall steel pipe piles of cylindrical shape and applies to pipe piles in which the steel cylinder acts as a permanent load-carrying member or as a shell to form case-in-place concrete piles. Surface imperfections exceeding 25% of the nominal wall in depth are considered defects. ASME SA 106 Grade B Carbon Steel Seamless Pipes FerropipeASME SA 106 Grade B Specification. ASME SA 106 Grade B Carbon Steel Seamless Pipes are Medium Carbon Steel Pipes with 0.3 % carbon content with combination of 0.29-1.06 % manganese. These Pipes are most commonly used for general purpose applications worldwide. ASME SA 106 Grade B Pipes are ductile and strong Pipes with long wearing properties.

ASME SA285 Grade C Middle or low strength carbon steel

The main difference for these three carbon steel grades of SA285 Grade A,SA285 Grade B and SA285 Grade C is their yield strength and tensile strength. For pressure vessel steel plate SA285 Grade A,minimum yield strength shall be 165 Mpa and 24Ksi,and SA285 Grade B pressure vessel steel plate owned the minimum yield strength at 185 Mpa and 27 ASTM A283 carbon steel plates properties and usages-ASTM ASTM A283 plate steel features low and intermediate tensile strength carbon steel plate of structural quality. It has four common variants, each represented as a separate material. The material properties section below shows ranges encompassing all variants. ASTM A285 Grade C Steel Plate Specifications - Octal SteelASTM A285 standard is for carbon steel, low and intermediate tensile strength steel plates intended for fusion-welded pressure vessels. The steel plate under ASTM A285 ranges in three grades, A, B and C, most common use is ASTM A285 Grade C plates. Which shall be made by killed, semi-killed, capped or rimmed steel practices at manufacturer's

ASTM A694 Flange Specifications (Grade F52, F60, F65

ASTM A694 F60, F65, F70, F52 Flange Specification. ASTM A694 refers to the material of carbon and alloy steel pipe flanges, fittings, valves and parts for high pressure liquid transmissions. It covers material grades of F42, F46, F50, F52, F56, F60, F65 and F70. Allowable stresses of typical ASME materials - Carbon SteelAt temperatures above 550°C, these stress values apply only when the carbon is 0.04% or higher on heat analysis. G21. For Section I, use is limited to PEB - 5.3. See PG - 5.5 for cautionary note. G24. A factor of 0.85 has been applied in arriving at the maximum allowable stress CSA G40.21 38W/260W Structural, Carbon & HSLA Steel CSA G40.21 38W/260W. A structural steel plate grade specified within G40.21 of the Canadian Standards Association (CSA). This grade is utilized in general fabrication and construction. It is also referred to as 260W, which is its metric designation. This material is also available as Charpy tested when referenced with a "T", such as 38WT / 260WT.

Comparing Steel Plate Grades

ABS Grade A, Grade B, Grade ADH36, Grade DH36, and Grade EH36:This steel is used almost exclusively in shipbuilding, especially in the construction of ships, barges, and marine equipment. It has a tensile strength of 58 to 71 ksi, and a minimum yield of 34 ksi. Plate Specification Guide 2015-2016 - ArcelorMittalGrade D A285 Grade A A285 Grade B A285 Grade C Type of Steel Carbon Carbon Carbon Carbon Carbon Requirements for Delivery A6 A6 A20 A20 A20 Tensile Strength (ksi) 55/75 60/80 45/65 50/70 55/75 Yield Strength (Min. ksi) (Yield Point if designated YP) 30 YP 33 YP 24 27 30 Spec. Thickness (Max. in.) - - 2 2 2 ArcelorMittal USA Thickness (Max. in SA-204 Steel Plates - American Alloy SteelOverview SA 204 Gr A, SA 204 Gr B & SA 204 Gr C. This carbon / molybdenum grade is used almost exclusively in Refinery / Petrochemical applications. The lean alloy characteristics of this grade lends itself to use in pressure vessels, fittings, and custom fabricated pipe and other environments within moderate temperature ranges. 1. 2.

Spiralco - Specifications - ASTM A-134

Note:When agreed upon between the purchaser and the manufacturer and so stated on the order, pipe may be tested to 1 and ½ times the specified working pressure, except that the maximum test pressure shall not exceed 2800 psi nor shall the maximum fiber stress exceed 85% of minimum yield point. Welding Research - American Welding Societyare A537 Grade B steel, a pressure vessel steel with minimum yield strength of 60 ksi (414 MN/2), and CON-PAC 80 , CON-PAC 90 and CON-PAC 100 steels with minimum yield strengths of 80, 90, and 100 ksi (552, 621, and 689 MN/m2), respec­ tively. Some of the quenched and tempered carbon steels are also avail­ able as abrasion-resistant steel plateA-283 Grade C, Grade D - American Alloy SteelGrade C. ksi (MPa) Tensile strength. 55-75 (380-515) 60-80 (415-550) Yield strength, min. 30 (205) 33 (230) Elongation in 8 in. or (200 mm), min, %B.